Start display at page:. Click again to stop recording. For more information refer to the complete User Manual located on the. Instruction for IE network monitor This system features a built-in browser-based software that allows you to access your system remotely over your local area network LAN or over the Internet WAN using. One Admin and four general User accounts are available. This user manual is an operation More information.
Backup File type includes Locked, Unlocked and All files. This manual, as well as the software Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book. Except as.. Setting Camera Order. Click Linkage Action tab to set hikvision 16 channel dvr user manual filetype alarm response actions of motion alarm please refer to Chapter 8.
User s Manual 3. Press this button to lock up the DVR unit; press I once again and a password window will appear; system can be unlocked only after inputting the correct password. Click OK hikvision 16 channel dvr user manual filetype finish the acitavting of the IP camera. Hikvision 16 channel dvr user manual filetype mode selected will be highlight with orange rectangle. This means that the product will.
Download the free trial version below to get started. Network settings must be properly configured before you operate DVR over network. RS setup Each channel is independent with H hardware compression. For some certain model of the speed dome, it can be configured to start a predefined park action scan, preset, patrol and etc. When the Coaxitron protocol is selected, all the other parameters like the baud rate, data bit, stop bit, parity and flow control are not configurable.
To import a configuration file, select the file from the selected backup device and click the Import button. With a hikvision 16 channel dvr user manual filetype alarm host configured, the DVR will send the alarm event or exception message to the host when an alarm is triggered.
This manual is applicable to. Open web browser, input the IP address of device, hikvision 16 channel dvr user manual filetype the web server will select the language automatically according to the system language and maximize the web browser. Click this icon to watch the Live view.
The content of this manual is furnished for informational use only, is subject. Click Linkage Action tab to set hikvision 16 channel dvr user manual filetype alarm response actions of motion alarm please refer to Chapter 8. User s Manual 3. Press this button to lock up the DVR unit; press I once again and a password window will appear; system can be unlocked only after inputting the correct password.
Click OK hikvision 16 channel dvr user manual filetype finish the acitavting of the IP camera. Hikvision 16 channel dvr user manual filetype mode selected will be highlight with orange rectangle. This means that the product will. Download the free trial version below to get started. Network settings must be properly configured before you operate DVR over network. RS setup Each channel is independent with H hardware compression. For some certain model of the speed dome, it can be configured to start a predefined park action scan, preset, patrol and etc.
When the Coaxitron protocol is selected, all the other parameters like the baud rate, data bit, stop bit, parity and flow control are not configurable. To import a configuration file, select the file from the selected backup device and click the Import button. With a hikvision 16 channel dvr user manual filetype alarm host configured, the DVR will send the alarm event or exception message to the host when an alarm is triggered.
This manual is applicable to. Enter the Manual Record setting menu. Switch between single screen and multi-screen mode. The default ID is This ID is valid for all IR remote controls.
Press the DEV button on the remote control. To use a USB mouse: Steps: 1. DB15 connector for VGA output. Display local video output and menu. Page 29 PTZ receiver respectively. Connector for alarm input. Page 32 While in the Shutdown menu Figure 2. Steps: 1. If you do not want to use the Setup Wizard at this time, click the Cancel button. Enter the admin password. By default, the password is You are highly recommended to change the default password right after the first login to avoid safety problem.
To initialize the HDD, click the Init button. Initialization will remove all the data saved in the HDD. Click Next button to enter the Record Settings window, as shown in Figure 2. Figure 2. So before you can get a live view or record of the video, you should add the network cameras to the connection list of the device.
The online cameras with same network segment will be displayed in the camera list. Click the button to add the camera. Or you can click the Add All button to add all the detected online IP cameras. Table 2. Enter the Camera Management interface. You can edit the network information and the password of the camera. Click Apply to save the settings and click OK to exit the interface. Page Introduction Of Live View 3.
This means if the HDMI is used, it will be the main output. Single Screen Switch to the single full screen by choosing channel number from the dropdown list. Instant Playback only shows the record in last five minutes. If no record is found, it means there is no record during the last five minutes.
Purpose: Sometimes you need to get a remote view of many channels in real time from web browser or CMS Client Management System software, in order to decrease the bandwidth requirement without affecting the image quality, channel-zero encoding is supported as an option for you.
You can configure the output interface, dwell time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc.
Page 51 User Manual of Digital Video Recorder 2 Click a window to select it, and then double-click a camera name in the camera list you would like to display. Enter the Manual Video Quality Diagnostics interface. Enter the PTZ Settings interface. When the Coaxitron protocol is selected, all the other parameters like the baud rate, data bit, stop bit, parity and flow control are not configurable.
Page Customizing Patrols 5. Click the Call Preset button to call it. Select patrol No. Click the Set button to add key points for the patrol. Figure 4. Configure key point parameters, such as the key point No. Click the button to show the general settings of the PTZ control. Select a patrol in the dropdown list and click the Call Patrol button to call it. Use the directional button to wheel the camera to the location where you want to set the limit, and click the Left Limit or Right Limit button to link the location to the corresponding limit.
Page One-Touch Park User Manual of Digital Video Recorder You can click the Restore button to clear the defined left limit and right limit data and the dome needs to reboot to make settings take effect.
Make sure that the HDD has already been installed. If not, please install a HDD and initialize it. Click Advance to check the storage mode of the HDD. Page 67 The Input Resolution of camera connected will be displayed in the live view for 5 seconds when the camera is connected, or the DVR is powered on. The input resolution includes the resolution and frame rate of the camera, e. Set encoding parameters for sub-stream. Figure 5. Enter the Record Schedule interface. And the time periods cannot be overlapped with each other.
Repeat the above steps 1 -4 to schedule recording for other days in the week. Click on the other area except for the schedule table to finish and exit the drawing. You can repeat step 4 to set schedule for other channels. Page Configuring Motion Detection Record Follow the steps to set the motion detection parameters. What we offer. Check the latest list of HDDs compatible with Hikvision's video recorders.
Manage Accept. Welcome to our site, this page need you to login with One Hikvision ID.
0コメント